How to Replace a Kia Sportage Replacement Key
For many Kia models, the key contains a built-in keyless entry system. This key typically resembles a remote control and is able to be replaced by a new one purchased from a Kia dealer or a locksmith.
Key fobs can stop working due to a variety of reasons, such as the battery being dead, worn-out buttons signal interference, or water damage. Here are some tips on how to program kia key fob; postheaven.net, to get your Kia Sportage replacement key back to working.
How do you replace the remote key or smartkey
The battery in your 2013 kia soul key fob programming's intelligent key will eventually need to be replaced, regardless of whether it's a remote key or a push-to-start one, or a normal metal key that does not contain an electronic transponder. This is especially true if the car displays a message telling that the remote or smart key has a low battery.
This is a relatively simple process. To replace the keyfob battery remove the mechanical key from the slit on the back of the fob. Then, pry the cover off. A small screw will be located inside the key fob to keep the battery in place. Remove the old battery by unwinding the screw with the help of a small screwdriver. Install the new battery and close the opening on the key fob.
Once the key fob has an updated battery Test it by pressing the locks and unlock buttons. If the doors unlock and lock exactly as you expect, then you're in good shape! You can now use the hands-free feature to lock and unlock your kia sportage key replacement when your fingers get chilly or when you need to run errands around Brandon.
Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of metal) do not require programming. If you need to reprogramme your key, you'll have to note the key code's number on the key code tag.
How do you replace a battery?
If the Kia key fob is unable to respond when you press the lock/unlock button, it is likely that the battery is low. A weak battery could cause other issues, such as the check engine light appearing or the engine not working properly. Fortunately replacing the key fob battery is a relatively simple DIY project that requires just a few tools.
Be sure to turn off your vehicle and shut all doors before you begin. Find the small metal or a plastic piece on the bottom of the key fob. Jiggle it until the metal key falls out. You can then insert the key into the door handle of the driver to unlock your car.
To replace the battery inside the key fob, take off the cover on the rear. Utilize a plastic plier tool to remove the latch that holds the black negative cable. Take the old battery out, and then place the new battery in a way that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.
After installing the new battery after which you turn the key fob on and off in the ignition until the door locks up. You can then test your kia ceed replacement key cost's keys fob to ensure it's working properly.
How do you replace the smart key
Depending on the model of the 2010 kia soul key fob programming Sportage, you may have an ordinary key fob or a smart key. The smart key has an embedded mechanical key blade unlike the standard key fob, which does not. Both key fobs are equipped with batteries that will eventually require replacing. Luckily, this is quite simple and will take about two minutes.
Before you get started it is important to make sure that you are on a flat surface with adequate lighting and that your Kia is turned off. Keep in mind that there are tiny pieces inside the fob which could fall out if not cautious.
The first step is to find the small release button on the lower backside of the fob. This will be either a circular button or rectangular slot. You can open the key fob by pressing the button.
Once the key fob is opened, take out the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. After you've finished, your key fob will allow you to lock, unlock, and start your vehicle even if it's not running.
How do you replace the mechanical key?
The Kia keyfob is a great convenience which allows us to lock or unlock our car by pressing a button. As with all devices it is possible that the Kia key fob may have issues. There are ways to address these issues and keep your key fobs working for many years.
A dead or weak battery is among the most frequent problems. This can cause your device to stop working or work intermittently. If this happens then try replacing the battery with a new one.
If this doesn't resolve the problem, try using a standard flathead screwdriver to open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed and replaced with a brand new one.
Once the new battery is in, shut and open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that can fit into the slot). Test the key fob to confirm it's working as intended. Contact a dealer or locksmith to solve the issue in the event that the fob is not working. To avoid lockouts in the future, ensure you have an emergency key that can work in all of the door and trunk cylinders.